14 kits found for Ring Gear Bolts

The tremendous shock loads generated at launch by most any drag racing vehicle equipped with today’s sticky tire compounds or the acceleration and deceleration of oval track cars put considerable strain on the ring gear. For this reason, the fastener experts at ARP Pro Series ring gear bolts are forged from premium grade 8740 chrome moly steel and are heat-treated to a nominal rating of 200,000 psi tensile strength. Specially hardened, precision-ground washers are included where required.

TECH NOTE - It is critically important to properly tighten ring gear bolts and make sure they don’t loosen. This is especially important in drag cars with tire shake. It’s also a good idea to check bolt tightness on a routine basis. If you use a locking compound (like Loc-Tite), it is best to install the ring gear first without any compound, then remove the bolts one at a time, reinstalling them with the compound. Be sure and torque each bolt before going on to the next one, because the locking compound sets up fast. Install and torque the bolts in an alternating or crossing pattern to distribute the load evenly around the ring gear.

Didn't find the kit you were looking for?
Application - Click for details Specifications Kit # Add to List
Tru-trac
Pro Series UHL Thread Size washers included
200,000psi 1.065˝ 7/16-14
300-3001
Dana 60
200-3001
Chrysler 7 1/4˝ & 8 3/4˝ (1972 & earlier) 0.390 grip, 12pt
Pro Series UHL Thread Size
200,000psi 0.835˝ 3/8-24
240-3001
Chrysler Clutch-type LSD-case half bolts, 12pt
Pro Series UHL Thread Size washers included
200,000psi 2.800˝ 3/8-24
250-3006
Strange Top Fuel, 12pt
Pro Series UHL Thread Size washers included
200,000psi 1.200˝ 7/16-20
250-3001
Ford 9˝, 5/8˝ wrenching, 12pt
Pro Series UHL Thread Size
200,000psi 0.940˝ 7/16-20
250-3002
Ford 8.8˝ & 9˝, 3/4" wrenching, 12pt
Pro Series UHL Thread Size
200,000psi 0.750˝ 7/16-20
250-3003
Ford 8˝, 12pt
Pro Series UHL Thread Size washers included
200,000psi 0.940˝ 7/16-20
250-3009
Ford, 12pt
Pro Series UHL Thread Size Shank Size washers included
200,000psi 1.060˝ 7/16-20 1/2˝
350-3004
GM 8.2˝ 10 & 12 bolt, 0.800˝ UHL, 8740, 12pt
Pro Series UHL Thread Size
200,000psi 0.800˝ 3/8-24
230-3001
GM 7.2˝, 7.5˝, 7.625˝ and 8.5˝ 10-bolt, 0.850˝ UHL, 12pt
Pro Series UHL Thread Size
200,000psi 0.850˝ 7/16-20 LH
230-3002
Volkswagen 020, 12pt
Pro Series UHL Thread Size nuts, washers included
200,000psi 1.200˝ M9 x 1.00
204-3001
Volkswagen 02A, 12pt
Pro Series UHL Thread Size nuts, washers included
200,000psi 1.180˝ M10 x 1.25
204-3002
Volkswagen 02M, 12pt
Pro Series UHL Thread Size nuts, washers included
200,000psi 1.100˝ M9 x 1.00
204-3003