| 166 kits found for Metric Thread Bolt Kits 8740 Chrome Moly - 5-Packs - All Sizes |
||
| 8740 CHROME MOLY: Until the development of today’s modern alloys, chrome moly was popularly considered a high strength material. Now viewed as only moderate strength, 8740 chrome moly is seen as a good tough steel, with adequate fatigue properties for most racing applications, but only if the threads are rolled after heat-treatment, as is the standard ARP production practice. Typically, chrome moly is classified as a quench and temper steel, that can be heat-treated to deliver tensile strengths between 180,000 and 210,000 psi. | ||
 |
|
Didn't find the kit you were looking for? |
| Diameter - Thread Pitch |
Under-head Length (UHL) | Socket Size | Kit # | Torque Value* | Add to List |
|---|
| M6 x 1.00 | 20mm | 8mm hex | 660-1001 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 25mm | 8mm hex | 660-1002 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 30mm | 8mm hex | 660-1003 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 35mm | 8mm hex | 660-1004 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 40mm | 8mm hex | 660-1005 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 45mm | 8mm hex | 660-1006 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 50mm | 8mm hex | 660-1007 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 55mm | 8mm hex | 660-1008 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 60mm | 8mm hex | 660-1009 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 65mm | 8mm hex | 660-1010 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 70mm | 8mm hex | 660-1011 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 75mm | 8mm hex | 660-1012 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 80mm | 8mm hex | 660-1013 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 90mm | 8mm hex | 660-1014 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 100mm | 8mm hex | 660-1015 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 12mm | 8mm hex | 660-1016 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 16mm | 8mm hex | 660-1017 | 11 ft-lbs (14.9 Nm) | |
| M6 x 1.00 | 135mm | 8mm hex | 660-1018 | 11 ft-lbs (14.9 Nm) | |
| M8 x 1.25 | 20mm | 10mm hex | 661-1001 | 24 ft-lbs (32.5 Nm) | |
| M8 x 1.25 | 25mm | 10mm hex | 661-1002 | 24 ft-lbs (32.5 Nm) | |
| M8 x 1.25 | 30mm | 10mm hex | 661-1003 | 24 ft-lbs (32.5 Nm) | |
| M8 x 1.25 | 35mm | 10mm hex | 661-1004 | 24 ft-lbs (32.5 Nm) | |
| M8 x 1.25 | 40mm | 10mm hex | 661-1005 | 24 ft-lbs (32.5 Nm) | |
| M8 x 1.25 | 45mm | 10mm hex | 661-1006 | 24 ft-lbs (32.5 Nm) | |
| *Torque notes: The torque values represented here are intended to be for general information only, not for specific installations. On specific installations, where the supplied instructions deviate from the torque values listed here, always follow the specific instructions packaged with the kit. Always lubricate the fastener prior to applying torque to ensure accurate readings. The values below are for use with ARP Ultra-Torque®. | |||||